The right leather jacket for your body type starts with your shape, not the label size. You find your build, pick a cut that suits it, and then check the fit on the bike. This guide walks you through each step. It covers slim, broad, boxy and round builds, and how the jacket should sit when you ride.
Fit matters more on a bike because you sit in a riding pose. You lean forward and your arms reach out to the bars. A jacket that looks fine when you stand can ride up at the back or pull at the shoulders. If the jacket has armor, it must also stay on your shoulders and elbows.
Stand in front of a mirror, then sit on your bike and reach for the bars. Watch three things. The back should still cover your lower back. The shoulders should not pinch. The sleeves should still reach your wrists.
Before you choose a size, measure yourself and compare the numbers with our motorcycle gear size chart. It also shows your waist and hip size in both inches and cm.
Your body shape tells you which cut will sit well. Most riders fit one of four builds: slim, athletic, boxy or round. Look at your shoulders, chest and waist in a mirror. Then take three tape measurements. The table below shows the key traits of each build and the cut that tends to suit it.
| Build | Key traits | Cut that suits it |
|---|---|---|
| Slim | Narrow shoulders, long arms, flat chest | Slim fit that follows the body |
| Athletic (V-shape) | Broad shoulders, slim waist | Room at the shoulders, a waist adjuster |
| Boxy | Shoulders and waist about the same width | Straight cut with side adjusters |
| Round | Fuller chest and belly | Straight cut, a little longer at the back |
To measure, use a soft tape and stand up straight. Wrap the tape around the fullest part of your chest. Then measure your waist where you wear your belt. For the sleeve, start at the center of your neck at the back. Go over the shoulder and down to the wrist with your arm bent a little.
A leather jacket for broad shoulders and a slim waist needs room up top and control at the waist. Size it to your chest and shoulders first. Then use a waist adjuster to take in the extra cloth. An action back helps too. That is a pleated or stretch panel that lets the back open up when you reach.
Check these points when you try one on:
The has a perforated action back. The has an action back with a stretch panel. For a shorter cut, the is waist length with a tab to adjust the waist.
Many riders with this build also like the short, close look of cafe racer motorcycle jackets.
A slim build suits a jacket cut close to the body. Pick the size that fits your chest, not one size up for longer sleeves. A big jacket on a slim rider puffs out in the wind and slides around. A slim cut stays flat, looks neat, and keeps the sleeves in place on the bars.
Boxy and round builds look and feel good in a straight cut. Avoid jackets that are tight at the belly or very short. Look for side adjusters so you can set the fit around your middle. Then sit on the bike and make sure the jacket does not ride up when you reach for the bars.
If your jacket has armor, the pads must sit on the joints they guard while you ride. Check the fit with your arms bent and your body leaned forward, as on the bike. Armor that sits right when you stand can slide off the joint once you reach for the bars.
You may see EN 1621-1 on a pad label. This is the European standard for impact pads at the shoulders, elbows, hips and knees. It has two levels. Level 2 lets less force through to the body than Level 1. For layers under the jacket, read our guide on how a motorcycle jacket should fit with layers.
A good leather jacket for riding has thick leather, a lining that suits the weather, and ways to adjust the fit. Look at the leather type and its thickness first. Then check the lining, the pockets, the waist adjuster, the vents, and the sleeve and back length in the riding pose. Use this checklist when you compare jackets.
Here is how the Biker jacket meets the list. It uses cowhide that is 1.1 to 1.3 mm thick. It has a satin lining, a zip-out liner and a perforated action back. It has four pockets outside and two inside. The sleeve cuffs zip closed, and there are side zips at the bottom.
To compare more cuts, browse our .
When no standard size fits your shape, a jacket made to your measurements is the next step. Many of our leather jackets offer a Custom Size option. You send your own measurements in place of a chart size. This helps riders with long arms, a broad back, or a chest and waist in different sizes.
Before you order a Custom Size, read how to measure so your numbers are right. For a full build, our are tailored in house to a made-to-measure fit. Sizes run from US 32 to 50 (EU 42 to 60). You can pick kangaroo, cowhide, sheep or goat leather. You can add perforation and vents. The jacket comes with CE-rated armor inside and outside.
Look at the leather type and thickness, the lining, and the pockets. Check for a waist adjuster so the jacket does not flap. Sit on your bike and make sure the sleeves reach your wrists and the back covers your belt. Only count on armor if the product details state it.
A slim build suits a slim cut that follows the body. Pick the size that fits your chest, not a bigger one for sleeve length. A removable liner lets you add warmth in the cold and keep a slim shape when it is mild.
Choose a jacket sized to your shoulders with the seam on the edge of the shoulder bone. An action back gives room to reach the bars. A tab or buckle at the waist takes in the extra cloth so the jacket does not flap.
A long leather coat is made for walking, not for the bike. On a motorcycle, a long coat bunches up when you sit. A riding jacket should end around the hip, so it covers your back when you lean but stays clear of the seat.
It should feel snug but not tight. The shoulder seam sits on the shoulder edge. You can zip it over a thin layer and still reach the bars with ease. The sleeves reach the wrist on the bike. For more on this, see how a motorcycle jacket should fit.